Skip to content

QN-248 · Quartz-vein-greisen tungsten (wolframite) type: quartz-wolframite veins with greisen rims up to 0.1–0.2 m thick (the rims carry poor wolframite mineralization); wolframite forms pocket and scattered disseminations in the quartz

Tungsten — East Kazakhstan Region

Channel samples from trenches across the veins (usual values, ranges by samples; not an average for a body):

WO₃ 0.2–0.5%

  • Host rocks: quartz-mica and quartz-sericite-mica schists of Late Devonian – Early Carboniferous age (D₃–C₁), greisenized; the schists contain dyke-like bodies of Permian plagiogranites, to which the authors genetically relate the mineralization. The weathering crust is thick, down to 70 m from the surface: intense ochre staining and cavities in the quartz filled with iron hydroxides. The occurrence is covered by Cenozoic deposits: Neogene clays on one side, and on the opposite flank the thickness of loose deposits increases sharply
  • Structural control: the veins are confined mainly to shear fractures, less often to tension fractures; the strike is nearly east-west, dipping south and south-east at 70–80°; the strike and dip of the veins conform with the dyke-like plagiogranite bodies. On one of the flanks the authors assume a sub-meridional fault
  • Dimensions: 21 quartz veins are known, 0.2–0.5 m thick, less often up to 2.2 m; along strike the veins are traced from 20–40 to 70–80 m (the ends are not outlined). At depth the veins were intersected by one drill hole at a depth of 80 m, and the thickness of the most persistent veins hardly changes there. According to the authors, the occurrence is not outlined either along strike or at depth
  • Secondary halo in loose deposits (metallometric survey on a 100 × 20 m grid over an area of 1 km²): an oval 700 × 400 m elongated north-south, across the strike of the veins — the authors explain this by the zone being cut off on one side and covered by thick loose deposits on the other; W 0.005–0.3% — halo values, not ore grade
  • Veins at the surface, channel samples from trenches: WO₃ usually 0.2–0.5% (range of ordinary samples, 2–4 samples per vein, rarely up to 6; not an average for a body); a single case of up to 2.2% WO₃ (one vein in one trench) — a single maximum value, not an average. The authors: some samples are diluted (channel length usually 2 m for veins 0.3–1.0 m thick), wolframite is probably replaced by iron hydroxides in the saprolite zone, so the low grades in vein samples are partly due to weathering
  • Drill hole: one hole, veins intersected down to a depth of 80 m — W no higher than 0.1 (the unit is not printed in the source) with core recovery in ore intervals of no more than 60%; the only intersection, with core loss, and the authors allow that wolframite may have crumbled out
  • Zones of disseminated mineralization (around the veins and on their continuation), outlined by spectral analysis: probably fine-disseminated mineralization in the schists and plagiogranites, as well as thin thread-like muscovite veinlets with wolframite (partly seen visually); strong weathering and iron staining make it hard to define the nature of the mineralization unambiguously. W from 0.1 to 0.3% and more — spectral analysis with a correction factor of 0.7 (spectral analyses of past years overstated grades; in one trench a chemical check was made on 17 samples); corrected spectral values, not an average for a body
  • Minerals: vein composition — quartz, muscovite, wolframite, limonite, tourmaline, rarely pyrite and arsenopyrite; according to the description of one trench, the quartz contains rare dissemination of coarse-pocket wolframite, pockets up to 5–7 cm across. Cassiterite and scheelite were found in heavy-mineral samples from eluvial-deluvial deposits (in the veins, as assumed by the authors, in minor amounts). Two wolframite samples: Nb₂O₅ 0.62% and 0.803%, Ta₂O₅ 0.03% and 0.005% (chemical analysis is stated for the second sample)
  • Degree of study: trenches and pits, channel sampling, a metallometric survey on a 100 × 20 m grid over an area of 1 km², lithogeochemical sampling, monomineral wolframite samples, one drill hole 159 m deep; during the geological re-inspection 4 pits and 2 trenches were dug, and the zones in one trench were re-sampled with a chemical check
  • Geologists’ predicted reserves (the authors’ estimate, not reserves by category; no category is named): roughly 300–400 t WO₃ at a conventionally assumed average grade of 0.5% for the four most persistent veins and parameters taken from the workings and the drill hole. Separately for the zones of disseminated mineralization (spectral grades with the 0.7 correction, depth extent of the zones taken as 15 m): zones of 0.1–0.3% (average 0.15%) — 110–120 t W; zones of 0.3% — 80–90 t W. The units differ (WO₃ and W), and the source gives no total

Report fragments

Source: archival geological reports (scans in our archive)

Location

The place is shown approximately: the object lies inside the circle. The exact place and materials follow a meeting.Region boundaries: © OpenStreetMap contributors, geoBoundaries (ODbL)
Contact