Skip to content

QN-202 · Copper mineralization of a secondary sulfide enrichment zone (as defined by the authors) in a weathering crust along a zone of tectonic dislocation and thrust; the ore body is vein-like (possibly a lens), dipping at 60–75°

Copper — Kostanay Region

Average for the ore body (authors' calculation from seven drill holes):

copper 4.73% at an average thickness of 2.53 m

  • The ore body lies at the junction of a large regional fault (dip 60–70°, displacement 300–400 m) with a series of other faults; the whole crush and weathering zone (about 200 m) carries copper, lead and zinc mineralization, with the maximum at the contact with limestones. Tectonic contact of red-colored sandstones and siltstones of the Upper Devonian with dolomitized limestones of the Upper Devonian; no intrusive rocks were encountered at the site
  • Ore body dimensions: about 200 m along strike and about 150 m down dip (150 and 100 m in the conclusion of the same report); thickness from 1.0 to 4 m, 2.53 m on average. 25–30 m above the main body a parallel zone 2–4 m thick with copper 0.3–0.65% is identified
  • Average for the ore body (the authors' calculation from seven drill holes): copper 4.73% at an average thickness of 2.53 m; range of copper contents in the body from 1.0 to 12%. In the author's table the sum of the thicknesses of the seven intersections is printed as 17.8 m, whereas the addition gives 18.8 m; at 18.8 m the average would be 4.48%
  • Average per working (drill-hole intersections, thickness — copper): 4.0 m — 7.80%; 1.2 m — 2.80%; 4.0 m — 2.32%; 1.0 m — 1.75%; 3.0 m — about 5.7% (a calculated value, the row is not fully printed in the source copy); 2.60 m — 3.60%; 3.0 m — 4.03%
  • Lead in the body averages 0.2–0.3%, zinc 0.1–0.3%, in individual samples up to 1–2%; in the oxidation zone copper from 0.1 to 0.65%, average 0.2–0.3%. In individual samples of lead-zinc mineralization in limestones (not the copper body), by spectral analysis silver up to 0.003%, gold up to 0.03 g/t
  • An external control analysis of four samples of the ore interval gave copper contents higher than the original ones (10.44; 12.70; 10.96 and 1.74%); the control is noted as “below the permissible” because of the small number of samples
  • The ore is a dark gray or black argillite-like clay with a small admixture of quartz sand and concretions of iron sulfides; ore minerals: chalcocite (61% of the heavy-mineral concentrate), native copper (17% of the concentrate), sphalerite, galena, pyrite, barite, apatite; in the oxidation zone chrysocolla, malachite, smithsonite, limonite
  • The weathering crust has elevated phosphorus: P2O5 in individual intervals 6–8%, in individual samples 14–17%. A small technological sample (2 kg, copper 10% in the original ore): a concentrate with copper 40.5% was obtained, but the yield was 4.1% and the recovery 16.6% because of the fine grain size of the ore (this is a beneficiation result, not a grade in the ore)
  • An approximate estimate by the authors: about 9 thousand t of copper (ore body volume 75,900 m³, ore density 2.5 t/m³, ore 189,750 t, copper 4.73%); no category — this is a forecast, not reserves
  • Level of study: core drilling, the ore body was intersected by seven drill holes (spacing along the profile 50 and 25 m, profiles 200 m apart), samples of 1.0–2.0 m from half of the core, chemical and spectral analysis. Primary ores were not intersected: in the dislocation zone the weathering crust descends 250–300 m; nine planned drill holes of 350 m each were not drilled (24% of the planned scope was completed), geophysics was not used, the form of the body at depth is unclear

Report fragments

Source: archival geological reports (scans in our archive)

Location

The place is shown approximately: the object lies inside the circle. The exact place and materials follow a meeting.Region boundaries: © OpenStreetMap contributors, geoBoundaries (ODbL)
Contact